Features
- Programmable Asynchronous State Machine
- Logic and Mixed Signal Circuits
- Highly Versatile Macrocells
- Read Back Protection (Read Lock)
- Four 150mA LDO Regulators
- I2C Interface
- 2.5V (±8%) to 5V (±10%) Supply
- Operating Temperature Range: -40°C to 85°C
- RoHS-Compliant/Halogen-Free
- Macrocells Overview
- Four Analog Comparators (ACMP)
- Voltage Reference (Vref) for ACMPs
- Analog Temperature Sensor
- Fifteen Combination Function Macrocells
- Three Selectable DFF/Latch or 2-bit LUTs
- Six Selectable DFF/Latch or 3-bit LUTs
- One Selectable Pipe Delay or Ripple Counter or 3-bit LUT
- Five 8-bit Delays/Counters or 3-bit LUTs
- Combinatorial Logic:
- One 4-bit LUT with Two Outputs
- Asynchronous State Machine
- Eight States
- Flexible Input Logic from State Transitions
- Real-Time Clock (RTC) Binary Counter
- Four Tri-Mode 150mA LDO Regulators
- High Power Mode (HP Mode): 150mA output
- Low Power Mode (LP Mode): 100μA output
- Bypass Mode: Acts Like a Load Switch
- 1A Synchronous DC/DC Step-Down Converter
- Serial Communications
- Proprietary 2-Wire interface "PC2W"
- I2C Slave Protocol Interface
- Programmable Delay with Edge Detector Output
- Additional Logic Functions
- 2 Deglitch Filters with Edge Detectors
- Two Oscillators (OSC)
- Configurable 25kHz/2MHz
- 2kHz Low Power Oscillator
- Eight-Byte RAM + OTP User Memory
- RAM Memory space that is readable and writable via I2C
- User-defined initial values transferred from OTP
- Power-On Reset (POR)
Description
The SLG46585 is a small, low-power component commonly used to integrate mixed-signal functions under the control of an asynchronous state machine. The user creates the circuit design by programming the one-time programmable (OTP) non-volatile memory (NVM) to configure the interconnect logic, the I/O pins, and the macrocells of the SLG46585. This highly versatile device allows for a wide variety of functions and control logic to be designed within a very small, low-power monolithic integrated circuit.
Parameters
| Attributes | Value |
|---|---|
| Nominal VDD | 2.5 - 5.5 |
| GPIOs (#) | 7 |
| Special Features | 4x LDO, ASM (8 states), DC/DC, RTC |
| ACMP Channels (#) | 4 |
| CNT/DLY (Max) (#) | 5 |
| LUTs (Max) (#) | 16 |
| D Flip-flops (DFFs) (#) | 9 |
| Pipe Delay | 16-stage |
| # of Programable Delays (#) | 1 |
| Oscillator Type | Conf. OSC, LF OSC |
| Temperature Sensor (ch) (#) | 1 |
| Interface | I2C |
| Memory Type | OTP |
| Temp. Range (°C) | -40 to +85°C |
Package Options
| Pkg. Type | Pkg. Dimensions (mm) | Lead Count (#) |
|---|---|---|
| MSTQFN | 3.0 x 3.0 | 29 |
Application Block Diagrams
 | High-End Feature-Rich HMI Platform Flexible HMI platform with rich feature support for display resolutions, audio, speakers, and more. |
 | Tiny Flexible System-on-Module (SoM) This flexible SoM integrates an MCU, FPGA, and programmable mixed-signal matrix onto a single board. |
Complete Your Design
Explore complementary products to elevate your design
Renesas Boards & Kits
GreenPAK SLG46585 (MSTQFN-29) 29-Pin DIP Prototyping Board
The SLG46585M-DIP 20-pin DIP prototyping board is perfect for breadboarding and fast prototyping using the SLG46585 programmable mixed-signal matrix with asynchronous state machine, LDOs, and DC/DC converter IC. It requires the SLG4SA-DIP DIP Adapter to use with the Advanced Development... Read More
GreenPAK SLG46585 Development Kit with Socket Adapter
The SLG46585M-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK™ Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The SLG46585M-SKT includes the SLG4SA29-30x30 socket adapter and 50 SLG46585M (MSTQFN-29) GreenPAK programmable mixed-signal matrix IC... Read More
GreenPAK Advanced Development Board
The GreenPAK™ Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK programmable mixed-signal devices - for use with SLG46xxxX-SKT/SLG47xxxV-SKT socket kits.
The board works in tandem with the GreenPAK Designer software (built into the Go... Read More
Test This Board Remotely
GreenPAK Serial Debugger Board (GSD)
The GreenPAK™ Serial Debugger (GSD) device can be used for programming GreenPAK programmable mixed-signal matrix IC products with multiple-time non-volatile memory (NVM) or for configuring the interconnect logic, the IOs, and the macrocells of all GreenPAK chips with an I²C interface. This... Read More
GreenPAK Lite Development Board
The GreenPAK™ Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in conjunction with the Go Configure™ Software Hub. Board functionality is provided by the RX66T MCU from Renesas.
Evaluation Board Kit for RZ/G3S MPU
This evaluation board kit is ideal for evaluating RZ/G3S. The RZ/G3S Evaluation Board Kit consists of a module board (SOM) and a carrier board. The module board complies with the SMARC v2.1 standard.
- Contents
- RZ/G3S SMARC Module board (SMARC2.1)
- RZ SMARC Series Carrier Board II
- RZ SMARC Series JTAG...
Evaluation Board Kit for RZ/G3E MPU
The RZ/G3E Evaluation Board Kit consists of a module board (SOM) and a carrier board, ideal for evaluating the features of the RZ/G3E MPU. The module board complies with the SMARC v2.1 standard and is a good reference for module board-based product development.
Main Contents:
- RZ/G3E SMARC Module... Read More
Partner Boards & Kits
RZ/G3E DX-M1 System on Module (SoM)
RZ/G3E OSM-L
RZ/G3E System on Module (SoM)
Support Communities
-
Learn how to use the SLG46585 DC/DC OCP feature
Check out the app note below to look into recommended application curcuit, when output voltage of DC/DC is 3 V or 3.3 V and the over current protection feature is enabled: https://www.dialog-semiconductor.com/an-cm-293
Apr 1, 2020 -
intermediate output voltage of DC/DC in SLG46585
There are 6 different Vout selectable in DC/DC. What is the best way for creating a Vout different from the 6 selectable (i.e. 2.8V)? Is it possible to work with a resitor devider at pin VOSNS? Thanks
Apr 5, 2019
Support Communities
