Overview
Description
Features
- Supports the motor control development support tool "Renesas Motor Workbench"
- Communication signals are connected to the CPU board via an isolator, enabling safe evaluation and debugging of motor control in an environment where the PC and CPU board are electrically isolated.
- It is possible to use boards other than Renesas CPU boards by embedding Renesas Motor Workbench compatible libraries (*1) in the motor control software.
*1 Supported MCUs are in accordance with the following supported CPU cards. - Supported CPU boards
- RX MCU:
- RX13T CPU Card (P/N: RTK0EMXA10C00000BJ) *2
- RX23T CPU Card (P/N: RTK0EM0003C01202BJ) *2
- RX24T CPU Card (P/N: RTK0EM0009C03402BJ) *2
- RX24U CPU Card (P/N: RTK0EMX590C02000BJ) *2
- RX66T CPU Card (P/N: RTK0EMX870C00000BJ) *2
- RX72T CPU Card (P/N: RTK0EMX990C00000BJ) *2
- RX72M CPU Card with RDC-IC (P/N: RTK0EMXDE0C00000BJ) *2
- RX26T CPU Board Type A (P/N: RTK0EMXE70C00000BJ) *included in RTK0EMXE70S00020BJ
- RX26T CPU Board Type B (P/N: RTK0EMXE70C01000BJ)
- RX26T CPU Board Type C (P/N: RTK0EMXE30C00000BJ)
- RA6T1 CPU Card (P/N: RTK0EMA170C00000BJ) *2
- RA6T2 CPU Board (P/N: RTK0EMA270C00000BJ) *included in RTK0EMA270S00020BJ
- RA6T3 CPU Board (P/N: RTK0EMA330C00000BJ) *included in RTK0EMA330S00020BJ
- RA4T1 CPU Board (P/N: RTK0EMA430C00000BJ) *included in RTK0EMA430S00020BJ
- RA8T1 CPU Board (P/N: RTK0EMA5K0C00000BJ) *included in RTK0EMA5K0S00020BJ
- RA8T2 CPU Board (P/N: RTK0EMA6L0C00000BJ) *included in RTK0EMA6L0S00020BJ
*2 compatible cable (included in RTK0EMX270S00020BJ and RTK0EMA170S00020BJ) is required
- RX MCU:
- Included items
- Communication board
- Accessories (cables, standoffs, etc.)
Applications
Design & Development
Videos & Training
Additional Videos
Support
Support Communities
- MC-COM Software
Hello. I want to make a motor driver. I print my own cards. At the same time, I want to make your MC_COM card and produce all of them. How can I access the software file of this card? How can I run it? TRANSLATE with x English Arabic ...
Feb 21, 2025 - OpenOCD support for RA2L1
Hello everyone! I'm trying to flash a program on the RA2L1 family Renesas microcontroller(specifically R7FA2A1AB3CFM). But unfortunately OpenOCD doesn't come with a config file for R7FA2A1AB3CFM by default. I tried using another config file called "openocd/tcl/target/renesas_s7g2.cfg" it can successfully ...
Nov 6, 2023 - DK-S124 CAN Bus Example
Is there a CAN Bus Example for the DK-S124? I need to know what the CAN Baud Rate Prescaler, Time Segments, etc. should be for the DK-S124 at 1Mbps CAN bandwidth. Where is the CAN MCLK coming from? Is it the 16Mhz crystal? If so, is it possible ...
Oct 4, 2017
Knowledge Base
- Why are there multiple package formats in bxl files for Synergy MCUs?
Question: Why are there multiple package formats in Synergy MCU bxl files? Answer: The bxl files for synergy MCUs comply with the IPC standard and thus present three different formats- the nominal, the minimum and the maximum. These are used by layout software to help optimize the device layout and ...
- When is RA6W1 ready to communicate with the host after waking from DPM sleep?
... INIT:WAKEUP,UC for unicast packet or +INIT:WAKEUP,EXT for external wakeup) to the host MCU. The host should then respond with the AT+MCUWUDONE command to indicate that it is fully awake and prepared to receive data. Upon receiving AT+MCUWUDONE, the RA6W1 resumes communication and starts sending ...
Dec 10, 2025 - Error message-Boot Failed-Communication Timeout Error_E8a_E8_E7
... E8/E7) emulator will also not operate normally.This could be caused by one of the following: (note that pin availability differs according to MCU)Common to all MCUs The MCU input clock is not within specifications or the crystal oscillator is not oscillating correctly. The MCU operating voltage ...
Oct 11, 2017
Support Communities
Knowledge Base
