Overview
Description
The SLG47011 provides a small, low-power solution for commonly used analog-to-digital conversion and mixed-signal functions. A flexible data acquisition system used in conjunction with configurable logic provides a way to implement a wide variety of functions with minimal cost. The user may create a circuit design by programming the one-time programmable (OTP) non-volatile memory (NVM), to configure the interconnect logic, the macrocells, and the IO pins.
Features
- 14-bit, 1Msps SAR ADC
- Sampling up to Four Analog Channels
- 14-, 12-, 10-, 8-bit Selectable Resolution
- Output Options: Parallel, I²C, SPI
- Programmable Gain Amplifier
- 1x to 64x Gain Selection
- Differential, Single-Ended Modes
- MathCore
- Multiplier, Adder, Subtractor, Shifter Options
- Four Independent Data Buffers
- Buffer Length up to Eight 16-bit Words
- Oversampling Mode (Increasing ADC Resolution)
- Moving Average Mode
- Counter Capture Mode
- 4096 Words x 12-bit Memory Table Macrocell
- Full Range Mode or Two Ranges Mode
- ADC Data Linearization or Any y = F(x) Function
- ADDR-to-DATA/Storage Modes
- 16-bit Multichannel Digital Comparator (MDCMP)
- Sampling up to Four Independent Channels
- Static or Dynamic Threshold
- Hysteresis Option for Each Channel
- PWM Macrocell
- 12-bit Resolution
- Dynamic Duty Cycle Change (up to 4096 Duty Cycle Value)
- Width Converter Macrocell
- 12-bit Parallel Data Output
- Optional 12 x 1-bit, 3 x 4-bit, 2 x 6-bit Output
- 12-bit 333ksps Digital-to-Analog Converter
- Selectable Current Source
- Integrated Voltage References (VREF)
- High-Speed Analog Comparator
- Configurable Hysteresis and reference
- Eighteen Combination Function Macrocells
- Two 2-bit LUT or DFF/LATCH Macrocells
- Eight 3-bit LUT or DFF/LATCH with Set/Reset
- Six Selectable DFF/LATCH or 3-bit LUTs or Shift Registers
- Two 4-bit LUT or DFF/LATCH with Set/Reset Macrocell
- Fourteen Multi-function Macrocells
- Ten Selectable DFF/LATCH or 3-bit LUTs + 12-bit Delay/Counters
- Two Selectable DFF/LATCH or 4-bit LUT + 16-bit Delay/Counter/FSM
- One Selectable DFF/LATCH or 3-bit LUTs + 12-bit Delay/Counter/FSM
- 12-bit Memory Control Up/Down Counter
- Communication Interfaces
- I²C Interface
- SPI Interface
- Programmable Delay with Edge Detector Output
- Deglitch Filter or Edge Detector
- Two Oscillators (OSC)
- 2kHz/10kHz Oscillator
- 20MHz/40MHz Oscillator
- Analog Temperature Sensor
- Power-on Reset (POR) with CRC
- Read Back Protection (Read Lock)
- Power Supply: 1.71V to 3.6V
- Operating Temperature Range: -40 °C to 85 °C
- RoHS-Compliant/Halogen-Free
- Available Package: 16-pin STQFN: 2.0mm x 2.0mm x 0.55mm, 0.4mm pitch
Comparison
Applications
Design & Development
Software & Tools
Software & Tools
| Software title
|
Software type
|
Company
|
|---|---|---|
| Go Configure Software Hub Go Configure Software Hub provides development support for a variety of products, including GreenPAK configurable mixed signal matrix and ForgeFPGA™ devices.
|
Software Package | Renesas |
1 item
|
||
Sample Code
Sample Code
| Sample Code | ZIP 35 KB | |
| Sample Code | ZIP 38 KB | |
| Sample Code | ZIP 13 KB | |
| Sample Code | ZIP 8 KB | |
| Sample Code | ZIP 8 KB | |
| Sample Code | ZIP 8 KB | |
| Sample Code | ZIP 9 KB | |
| Sample Code | ZIP 7 KB | |
| Sample Code | ZIP 8 KB | |
9 items
|
||
Boards & Kits
Development
SLG47011V-EVB
Active
AnalogPAK SLG47011 Evaluation Board
The SLG47011V-EVB evaluation board is used to show the superior performance of the SLG47011V programmable mixed-signal matrix as a small, low-power component used in analog-to-digital conversion and mixed-signal functions.
The evaluation board is a compact, easy-to-use hardware tool that provides...
Recommended Documents:
Development
SLG47011V-SKT
Active
AnalogPAK SLG47011V Development Kit with Socket Adapter
The SLG47011V-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The SLG47011V-SKT kit includes the SLG4SA16AA-20x20 socket adapter and 50 SLG47011V GreenPAK programmable mixed-signal matrix IC samples.
Used...
Recommended Documents:
Development
SLG47011V-DIP
Active
AnalogPAK SLG47011 20-Pin DIP Prototyping Board
The SLG47011V-DIP 20-pin DIP Prototyping Board is perfect for breadboarding and fast prototypes. It requires the DIP Adapter (SLG4SA-DIP) to use it with the GreenPAK™ Advanced Development Board.
Recommended Documents:
Demonstration
SLG47011V-USBPWR-DMO
Active
AnalogPAK SLG47011V USB Power Demonstration Board
The SLG47011V demonstration board is a compact, easy-to-use, USB Type-C powered hardware tool for measurement of voltage, current, power, and temperature. The SLG47011 IC provides measurement using PGA/ADC and the Renesas RL78/G13 MCU supports the operation of the display.
Recommended Documents:
Demonstration
SLG47011V-HART-DMO
Active
AnalogPAK SLG47011 HART Modem Demonstration Board
The SLG47011V HART Modem is a demonstration board that shows the implementation of the industrial HART protocol on a mixed-signal IC from Renesas. The board contains both logical parts - Host Device and Field Device - to respectively simulate the work of the master (controller) and the remote...
Recommended Documents:
Development
SLG4DVKADV
Active
GreenPAK Advanced Development Board
The GreenPAK™ Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK devices - for use with SLG46xxxX-SKT/SLG47xxxV-SKT socket kits.
It works in tandem with the GreenPAK Designer software (built into the Go Configure™ Software Hub), and it allows...
Recommended Documents:
Test This Board Remotely
Available on Lab on the Cloud, use our PC-based GUI to instantly start configuring and testing designs in our virtual lab, no physical board needed.
Development
SLG4DVKLITE
Active
GreenPAK Lite Development Board
The GreenPAK™ Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in conjunction with the Go Configure™ Software Hub. Board functionality is provided by the RX66T MCU from Renesas.
Recommended Documents:
Development
SLG4DVKLITEINTRO-KIT
Active
GreenPAK Introduction Kit Lite
The SLG4DVKLITEINTRO GreenPAK™ Introduction Kit is perfect for customers starting new development with the GreenPAK programmable mixed-signal products.
Recommended Documents:
Development
SLG4SA-DIP
Active
GreenPAK DIP Adapter for GreenPAK Advanced Development Board
The GreenPAK™ DIP Adapter for the GreenPAK Advanced Development Board allows for using the SLG46xxxV-DIP and SLG47xxxV-DIP prototyping boards with the GreenPAK Advanced Development Board. It acts as the bridge between the advanced and DIP development platforms.
Recommended Documents:
Development
SLG4DVKGSD
Active
GreenPAK Serial Debugger Board (GSD)
The GreenPAK™ Serial Debugger (GSD) device can be used for programming GreenPAK programmable mixed-signal matrix IC products with multiple-time non-volatile memory (NVM) or for configuring the interconnect logic, the IOs, and the macrocells of all GreenPAK chips with an I²C interface. This...
Recommended Documents:
Models
ECAD Models
Schematic symbols, PCB footprints, and 3D CAD models from SamacSys can be found by clicking on the CAD Model links in the Product Options table. If a symbol or model isn't available, it can be requested directly from SamacSys.
Models
| Model - Other | ZIP 9.81 MB | |
1 item
|
||
Product Options
Applied Filters:
Support
Support Communities
Get quick technical support online from Renesas Engineering Community technical staff.
Support Communities
-
Missing DAC Output using the SLG47011V
Hello,I am planning to use the GreenPak SLG47011 for some simple filtering and amplification. Everything works as expected in the simulation, but during emulation there is no DAC Output on the PIN12. The signal follows this path: PIN9, PGA, ADC, Memory Table, DAC, PIN12.Am I missing something here ...
Jul 21, 2025 -
SLG47011V does not respond
... should avoid smoke to leave the room. Attempt in software to connect leads to "The chip is either absent or positioned incorrectly.". * Same result with SLG47011V-DIP board. It has no way to connect GPSD directly but I used some dupont wires. Same error message. Unsure how to encourage SLG47011V ...
Jan 26, 2025 -
SLG47011V EVB communication error
Hello, I'm using GreenPAK LDB Rev 1.1 & SLG47011V EVB, and the simulation is working fine. But when I try to emulate/sync, I am unable to connect with EVB. Throwing the below error. Urgent: Demo planned for early next week
Jul 25, 2025
FAQs
-
Can I use SLG47011 in battery-powered applications?
Last Updated: 06/24/2025 Question: Can I use SLG47011 in battery-powered applications? Answer: Yes, its ultra-low power sleep mode (~0.6 µA) and small package size make it well-suited for portable and battery-operated designs. Suitable Products SLG47011
Jun 24, 2025 -
Does SLG47011 include EEPROM or flash memory?
Last Updated: 06/24/2025 Question: Does SLG47011 include EEPROM or flash memory? Answer: No, it includes only one-time programmable (OTP) memory and volatile RAM for configuration during development. Suitable Products SLG47011
Jun 24, 2025 -
What development tools are available for the SLG47011?
Last Updated: 06/24/2025 Question: What development tools are available for the SLG47011? Answer: Renesas provides an evaluation board (SLG47011V-EVB), a DIP adapter, and socket kits for prototyping and programming. Suitable Products SLG47011
Jun 24, 2025
Videos & Training
SLG47011 AnalogPAK Programmable Mixed-Signal Matrix Overview
The low-cost, low-power SLG47011 is an AnalogPAK™ programmable mixed-signal matrix with a 14-bit ADC and analog features.
Video List
