Features
- Dual P-FET Power Switch
- Read Back Protection (Read Lock)
- Power Supply: 2.5V (±8%) to 5V (±10%)
- Operating Temperature Range: -40°C to 85°C
- RoHS Compliant/Halogen-Free/Pb-Free
- Macrocells Overview
- Two High-Speed General-Purpose Analog Comparators (ACMPxH)
- Two Low-Power General-Purpose Analog Comparators (ACMPxL)
- Two Voltage References (Vref)
- Two Vref Outputs
- Fifteen Combination Function Macrocells
- Three Selectable DFF/Latch or 2-bit LUTs
- One Selectable Programmable Pattern Generator or 2-bit LUT
- Nine Selectable DFF/Latch or 3-bit LUTs
- One Selectable Pipe Delay or Ripple Counter or 3-bit LUT
- One Selectable DFF/Latch or 4-bit LUTs
- Eight Multi-Function Macrocells
- Seven Selectable DFF/Latch or 3-bit LUTs + 8-bit Delay/Counters
- One Selectable DFF/Latch or 4-bit LUT + 16-bit Delay/Counter
- Serial Communications
- I2C Protocol Interface
- Programmable Delay with Edge Detector Output
- Deglitch Filter or Edge Detector
- Three Oscillators (OSC)
- 2.048kHz Oscillator
- 2.048MHz Oscillator
- 25MHz Oscillator
- Analog Temperature Sensor
- Power-On Reset (POR)
Description
The SLG46867 provides a small, low-power component for commonly used mixed-signal functions. The user creates their circuit design by programming the one-time programmable (OTP) non-volatile memory (NVM) to configure the interconnect logic, the IO pins, and the macrocells of the SLG46867. This highly versatile device allows a wide variety of mixed-signal functions to be designed within a very small, low-power single integrated circuit.
Parameters
| Attributes | Value |
|---|---|
| Special Features | 2x P-FET (44Ω,2A) |
| GPIOs (#) | 12 |
| Nominal VDD | 2.3 - 5.5 |
| ACMP Channels (#) | 4 |
| CNT/DLY (Max) (#) | 8 |
| LUTs (Max) (#) | 23 |
| D Flip-flops (DFFs) (#) | 21 |
| Pipe Delay | 16-stage |
| # of Programable Delays (#) | 1 |
| Oscillator Type | RC OSC, LF OSC, Ring OSC |
| Temperature Sensor (ch) (#) | 1 |
| Interface | I2C |
| Memory Type | OTP |
| Temp. Range (°C) | -40 to +85°C |
Package Options
| Pkg. Type | Pkg. Dimensions (mm) | Lead Count (#) |
|---|---|---|
| MSTQFN | 1.6 x 3.0 | 20 |
Applications
- Power Sequencing with Complex Analog Control
- Power Plane Component Size Reduction Project
- Consumer Electronics
- LED Drivers
- Haptic Motor Drivers
- System RESET with Power Switch
Renesas Boards & Kits
GreenPAK SLG46867 Development Kit with Socket Adapter
The SLG46867M-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK™ Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The SLG46867M-SKT kit includes the SLG4SA20-16x30 socket adapter and 50 SLG46867M GreenPAK programmable mixed-signal matrix IC samples.
Used... Read More
GreenPAK SLG46867 20-Pin DIP Prototyping Board
The SLG46867M-DIP 20-pin DIP prototyping board is perfect for breadboarding and fast prototyping with the SLG46867 programmable mixed-signal matrix with dual supply IC. It requires the SLG4SA-DIP DIP Adapter to use with the GreenPAK™ Advanced Development Board.
The GreenPAK™ DIP Adapter is a... Read More
GreenPAK Advanced Development Board
The GreenPAK™ Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK programmable mixed-signal devices - for use with SLG46xxxX-SKT/SLG47xxxV-SKT socket kits.
The board works in tandem with the GreenPAK Designer software (built into the Go... Read More
Test This Board Remotely
GreenPAK DIP Adapter for GreenPAK Advanced Development Board
The GreenPAK™ DIP Adapter for the GreenPAK Advanced Development Board allows for using the SLG46xxxV-DIP and SLG47xxxV-DIP prototyping boards with the GreenPAK Advanced Development Board. It acts as the bridge between the advanced and DIP development platforms.
GreenPAK Serial Debugger Board (GSD)
The GreenPAK™ Serial Debugger (GSD) device can be used for programming GreenPAK programmable mixed-signal matrix IC products with multiple-time non-volatile memory (NVM) or for configuring the interconnect logic, the IOs, and the macrocells of all GreenPAK chips with an I²C interface. This... Read More
GreenPAK Lite Development Board
The GreenPAK™ Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in conjunction with the Go Configure™ Software Hub. Board functionality is provided by the RX66T MCU from Renesas.
Support Communities
-
DFF not working with different IO pins
... not repsond properly. I have the DFF reset tied to an input pin. If I remove the DFF, and connect directly to the OR gate, it responds to the PIN inputs correctly. I am using Greenpak Design 6.22 (build 006) and the Advanced Developement Platform with the SLG46867M. Thanks
Jul 16, 2020 -
My GreenPAK orderf was not sent
... Order Confirmation Order #548 details: 1 x GreenPAK DIP Development Board$29.99 2 x SLG47105V-DIP$2.50 2 x SLG47004V-DIP$2.50 2 x SLG46867M-DIP$2.50 2 x SLG46517M-DIP$2.50 3 x SLG46108V-DIP$3.75 2 x SLG46855AP-DIP$2.42 Shipping Information Billing Information Payment Method PayPal ...
Jun 6, 2022 -
Software Simulation ending time greater then 1ks - GreenPAK Go Configure
Hi,i need to configure ending time in "Software Simulation" greater than 1ks to validate my watch dog circuit. My setup is SLG46867M, Go Configure Software Hub Version 6.49(Build 001) Windows 11.The software suggest Recommended range is 1fs to 1ks but is not a limit see image ...
Aug 5, 2025
Support Communities
