Features
- Drives N-Channel FET Full Bridge Including High Side Chop Capability
- Bootstrap Supply Max Voltage to 95VDC
- Drives 1000pF Load at 1MHz in Free Air at +50°C with Rise and Fall Times of Typically 10ns
- User-Programmable Dead Time
- Charge-Pump and Bootstrap Maintain Upper Bias Supplies
- DIS (Disable) Pin Pulls Gates Low
- Input Logic Thresholds Compatible with 5V to 15V Logic Levels
- Very Low Power Consumption
- Undervoltage Protection
- Pb-Free Available as an Option
Description
The HIP4080A is a high frequency, medium voltage Full Bridge N-Channel FET driver IC, available in 20 lead plastic SOIC and DIP packages. The HIP4080A includes an input comparator, used to facilitate the hysteresis and PWM modes of operation. Its HEN (high enable) lead can force current to freewheel in the bottom two external power MOSFETs, maintaining the upper power MOSFETs off. Since it can switch at frequencies up to 1MHz, the HIP4080A is well suited for driving Voice Coil Motors, switching power amplifiers and power supplies. HIP4080A can also drive medium voltage brush motors, and two HIP4080As can be used to drive high performance stepper motors, since the short minimum on-time can provide fine micro-stepping capability. Short propagation delays of approximately 55ns maximize control loop crossover frequencies and dead-times which can be adjusted to near zero to minimize distortion, resulting in precise control of the driven load. The similar HIP4081A IC allows independent control of all 4 FETs in a Full Bridge configuration.
Parameters
| Attributes | Value |
|---|---|
| Bootstrap Supply Voltage (Max) (V) | 95 |
| VBIAS (Max) (V) | 15 |
| Peak Pull-up Current (A) | 2.6 |
| Peak Pull-down Current (A) | 2.4 |
| Turn-On Prop Delay (ns) | 70 |
| Turn-Off Prop Delay (ns) | 50 |
| Rise Time (μs) | 0.01 |
| Fall Time | 10 |
| Temp. Range (°C) | -40 to +85°C |
| Input Logic Level | 3.3V/TTL |
| Qualification Level | Standard |
Application Block Diagrams
 | Digital Power Conversion with Totem Pole Interleaved PFC High-efficiency power supply platform featuring totem pole PFC and LLC resonant DC/DC converters. |
Additional Applications
- Medium/Large Voice Coil Motors
- Full Bridge Power Supplies
- Switching Power Amplifiers
- High Performance Motor Controls
- Noise Cancellation Systems
- Battery Powered Vehicles
- Peripherals
- UPS
Complete Your Design
Explore complementary products to elevate your design
Renesas Boards & Kits
80V/2.5A Peak, High Frequency Full Bridge FET Driver Evaluation Board
The HIP4080A/81AEVALZ evaluation board is used to demonstrate theHIP4080A andHIP4081A 80V/2.5A peak, high frequency, full bridge FET drivers with charge pump and input comparators.
The HIP4080A and HIP4081A are high frequency, medium voltage full bridge N-channel FET driver ICs, available in... Read More
Knowledge Base
-
HIP4080, HIP4080A, HIP4081 or HIP4081A Spice Model
There is an old Spice model floating around the web and I have attached it for your convenience. It is provided with no warranty and has not been verified. Make sure you read the entire "readme.txt". Below are excerpts from that: MACRO MODELS FOR HIP4080, HIP4080A, HIP4081, AND HIP4081A ...
May 6, 2024 -
What are some basic protection circuit suggestions when using HIP4080A and HIP4081A in motor control circuits?
Question:What are some basic protection circuit suggestions when using HIP4080A and HIP4081A in motor control circuits? Answer: The CR1 and CR2 (bootstrap diodes) - We recommend using a diode with Trr less than 50ns (UF4002, Microsemi Corp.) When you detect shoot-through, one cause could be that the MOSFETs turn ...
-
What are the suggested values for the components shown in Figure 3 of the HIP4080A app note, AN9404?
Question:Can you provide the suggested values for the components shown in Figure 3 of AN9404? Answer:Please try these values. RO=1k, RI=1k, C1=470pF, R1=10k, R2=1k, R3=200k and R4=50k. You may still need to tweak these a little depending on the desired hysteresis ...
Support Communities
