Overview
Description
The SLG47001 provides a small, low-power component for commonly used analog signal processing and mixed-signal functions. Individual tunable analog components used in conjunction with configurable logic provide a way to solve a wide variety of tasks with minimal costs. The user creates their circuit design by programming the one-time programmable (OTP) non-volatile memory (NVM) to configure the interconnect logic, the macrocells, and the IO pins of the SLG47001.
Features
- Two Operational Amplifiers (Op Amp) with Ultra-low Power Consumption
- Rail-to-Rail Input and Output (RRIO)
- Ultra-low Offset Voltage
- Zero Offset Voltage Drift
- Integrated Voltage Reference (VREF)
- Multi-channel Sampling Analog Comparator (MS-ACMP)
- Sampling up to Six Analog Channels
- Selectable Voltage Reference for Each Channel
- Different Sampling Scenarios
- Synchronous or Asynchronous Result Appearance
- Range Comparator Mode
- Two 1024-Position 100kΩ Digital Rheostats
- Potentiometer Mode
- I²C and Manual Control Options
- Extended Pattern Generator (EPG)
- Width Converter Option
- 8-bit Parallel Data Output
- Optional 1x 8-bit, 2x 4-bit, 4x 2-bit, or 8x 1-bit Serial Bitstream Output
- 59 Bytes Pattern Stored in NVM
- 11 Combination Function Macrocells
- Two 2-bit LUTs or DFF/LATCHs
- Four 3-bit LUTs or DFF/LATCHs with Reset/Set
- Four 3-bit LUTs, DFF/LATCHs, or Shift Registers
- One 4-bit LUT or DFF/LATCH with Reset/Set
- Five Multi-function Macrocells
- Four Selectable DFF/LATCHs or 3-bit LUTs + 8-bit Delay/Counters
- One Selectable DFF/LATCHs or 3-bit LUT + 8-bit Delay/Counter/FSM
- Programmable Delay with Edge Detector Output
- Two Oscillators (OSC)
- 2.048kHz/10kHz Oscillator with Ultra-low Current Consumption
- 25MHz Oscillator
- One Single-Pole/Single-Throw Analog Switch
- Analog Temperature Sensor
- Power-on Reset (POR) with CRC
- I²C Compatible Serial Interface
- Read Back Protection (Read Lock)
- 2.3V to 5.5V of VDD Range
- Operating Temperature Range: -40°C to +85°C
- RoHS-Compliant/Halogen-Free
- Available Package: 20-pin STQFN: 2.0mm x 3.0mm x 0.55mm, 0.4mm Pitch
Comparison
Applications
Documentation
Featured Documentation
Log in required to subscribe
|
|
|
|
|---|---|---|
| Type | Title | Date |
| Datasheet | PDF 5.11 MB | |
| Brochure | PDF 5.41 MB 日本語 | |
| White Paper | PDF 501 KB | |
3 items
|
||
Design & Development
Software & Tools
Software & Tools
| Software title
|
Software type
|
Company
|
|---|---|---|
| Go Configure Software Hub Go Configure Software Hub provides development support for a variety of products, including GreenPAK configurable mixed signal matrix and ForgeFPGA™ devices.
|
Software Package | Renesas |
1 item
|
||
Boards & Kits
Development
SLG47001V-SKT
Active
AnalogPAK SLG47001V Development Kit with Socket Adapter
The SLG47001V-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The SLG47001V-SKT kit includes the SLG4SA20AL-20x30 socket adapter and 50 SLG47001V GreenPAK programmable mixed-signal matrix IC samples.
Used...
Recommended Documents:
Development
SLG4DVKADV
Active
GreenPAK Advanced Development Board
The GreenPAK Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK devices - for use with SLG46xxxX-SKT / SLG47xxxV-SKT socket kits.
It works in tandem with the GreenPAK Designer software (built into Go Configure™ Software Hub), and it allows...
Recommended Documents:
Test This Board Remotely
Available on Lab on the Cloud, use our PC-based GUI to instantly start configuring and testing designs in our virtual lab, no physical board needed.
Development
SLG4DVKLITE
Active
GreenPAK Lite Development Board
The GreenPAK Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in a pair with the Go Configure™ Software Hub. Board functionality is provided by the RX66T MCU from Renesas.
Recommended Documents:
Models
ECAD Models
Schematic symbols, PCB footprints, and 3D CAD models from SamacSys can be found by clicking on the CAD Model links in the Product Options table. If a symbol or model isn't available, it can be requested directly from SamacSys.
Product Options
Applied Filters: