5P49V5933

VersaClock 5 Low Power Programmable Clock Generator with Integrated Crystal

Alternative(s) Available

5P49V6975 - VersaClock 6E Programmable Clock Generator with Integrated Crystal

Features

2 differential outputs LVPECL, LVDS, HCSL - or 2 LVCMOS outputs
<0.7ps RMS typical phase jitter on outputs
Two fractional output dividers (FODs)
Independent spread spectrum capability on each output pair
Stores 4 different configurations in OTP non-volatile memory
Up to 350MHz input/output frequencies
Redundant clock inputs with manual switchover
Programmable loop bandwidth, output to output skew, slew rate control
Individual output enable/disable
Meets PCIe^® Gen 1/2/3, USB 3.0, 1/10 GbE clock requirements
1.8/2.5/3.3V core and output voltages
4mm x 4mm 24-pin VFQFPN package
-40 °C to +85 °C operating temperature range
Supported by Renesas' Timing Commander™ software tool

Find Other Products in Clock Generation

5P49V5933 Block Diagram

5P49V5933 Pinout

5P49V5933 Block Diagram

5P49V5933 Block Diagram

Description

The 5P49V5933 is a programmable clock generator intended for high-performance consumer, networking, industrial, computing, and data communications applications. Configurations may be stored in on-chip One-Time Programmable (OTP) memory or changed using an I²C interface. This is Renesas' fifth generation of programmable clock technology (VersaClock^® 5). The 5P49V5933, by default, uses an integrated 25MHz crystal as an input reference. It also has a redundant external clock input. A glitchless manual switchover function allows the selection of either input reference during normal operation.

Two select pins allow up to 4 different configurations to be programmed and accessible using processor GPIOs or bootstrapping. The different selections may be used for different operating modes (full function, partial function, partial power-down), regional standards (US, Japan, Europe), or system production margin testing. The device may be configured to use one of two I²C addresses to allow multiple devices to be used in a system.

This device is factory-configurable.
Try the Custom Part Configuration Utility.

Applications

Ethernet switch/router
PCI Express 1.0/2.0/3.0
Broadcast video/audio timing
Multi-function printer
Processor and FPGA clocking
Any-frequency clock conversion
MSAN/DSLAM/PON
Fiber Channel, SAN
Telecom line cards
1GbE and 10GbE

This device is factory-configurable.
Try the Custom Part Configuration Utility.

Part Number	Status	Samples	Stock	Package	Budgetary Price (USD)	Lead Count (#)	Carrier Type	Moisture Sensitivity Level (MSL)	Qty. per Reel (#)	Qty. per Carrier (#)	Pb (Lead) Free	Pb Free Category	Temp. Range (°C)	Country of Assembly	Country of Wafer Fabrication
5P49V5933A000LTGI	NRND	Available	Out of Stock	LGA		24#	Tray	3	0	490#	Yes	e4 Au	-40 to 85°C
5P49V5933A000LTGI8	NRND	N/A	Out of Stock	LGA		24#	Reel	3	2500#	0	Yes	e4 Au	-40 to 85°C
5P49V5933B000LTGI	NRND	Available	In Stock	LGA	1ku \| $3.68	24#	Tray	3	0	490#	Yes	e4 Au	-40 to 85°C	TAIWAN	SINGAPORE
5P49V5933B000LTGI8	NRND	N/A	Out of Stock	LGA	1ku \| $3.68	24#	Reel	3	2500#	0	Yes	e4 Au	-40 to 85°C	TAIWAN	SINGAPORE

Loading

Filters

Recommended Documents (1)

Datasheet
5P49V5933 Datasheet
RECOMMENDED
PDF 498 KB 7WDXRDKU4E7E-5-58990 Nov 01, 2017

Datasheets (1)

Datasheet
5P49V5933 Datasheet
RECOMMENDED
PDF 498 KB 7WDXRDKU4E7E-5-58990 Nov 01, 2017

Manuals & Guides (4)

Manual - Development Tools
VersaClock 5 Family Register Descriptions and Programming Guide
PDF 1.25 MB 7WDXRDKU4E7E-5-57450 Feb 02, 2023
Manual - Development Tools
VersaClock 5 Programmer Board User Guide
PDF 549 KB 7WDXRDKU4E7E-5-57217 Dec 08, 2015
Manual - Software
VersaClock 5 Timing Commander Users Guide
PDF 2.04 MB 7WDXRDKU4E7E-5-57026 Oct 07, 2015
Manual - Hardware
VersaClock 5 Evaluation Board Users Guide
PDF 725 KB 7WDXRDKU4E7E-5-57025 Apr 29, 2015

Application Notes & White Papers (15)

Application Note
PCB Layout Considerations for VersaClock Clock Generator Family
PDF 1.09 MB R31AN0026EU0102 Rev.1.02 Sep 06, 2025
Application Note
Termination Options for High-Speed LVCMOS Driver Clock Drivers
PDF 187 KB R31AN0065EU0101 Rev.1.01 Nov 14, 2023
Application Note
Timing Commander Installation Guide
PDF 348 KB R31AN0040EU0100 Rev.1.00 Mar 10, 2023
Application Note
AN-1014 Microstrip vs Stripline: Crosstalk and RMS Phase Jitter
PDF 486 KB 7WDXRDKU4E7E-5-63374 Nov 01, 2018
Application Note
AN-975 Cascading PLLs
PDF 255 KB 7WDXRDKU4E7E-5-61774 Aug 02, 2017

Product Notices (PCN, EOL, etc) (2)

Product Change Notice
PCN# : W1602-01 300mm wafer size from 200mm wafer size at Global Foundries
PDF 344 KB 7WDXRDKU4E7E-5-59950 Feb 20, 2016
Product Change Notice
PCN# : MM1510-01 Programming Configuration Change on Versa Clock
PDF 243 KB 7WDXRDKU4E7E-5-59639 Oct 29, 2015

Schematics & Design Files (2)

Schematic
5P49V5933 Reference Schematic
PDF 44 KB 7WDXRDKU4E7E-5-58992 Apr 26, 2016
Schematic
VersaClock 5 Programmer Board Schematic
PDF 30 KB 7WDXRDKU4E7E-5-57802 Oct 02, 2014

Marketing Collateral (1)

Product Brief
5P49V5933 / 5P49V5935 VersaClock® 5 Programmable Clocks with Integrated Crystal Product Brief
PDF 945 KB 7WDXRDKU4E7E-6-10285 May 19, 2015

Renesas Boards & Kits

5P49V5933/35 VersaClock 5 with Integrated Crystal Evaluation Board - Top

Evaluation Board for 5P49V5933 VersaClock 5 with Integrated Crystal

This is the evaluation board for the Renesas 5P49V5933 VersaClock^® 5 programmable clock generator with integrated crystal. With RMS phase jitter less than 0.7 picoseconds over the full 12kHz to 20MHz integration range, the device meets the stringent jitter requirements of PCI Express^® Gen 1/2/3,... Read More

Recommended Documents:

VersaClock 5 5P49V5935/5933 Evaluation Boards User Guide

This video provides an overview of the VersaClock 5 programmable clock generator family, including the 5P49V5901, 5P49V5913, 5P49V5914, 5P49V5923, 5P49V5925, 5P49V5927, 5P49V5929.

The VersaClock 5 family is an in-system programmable clock generator featuring up to four universal output pairs capable of producing independent frequencies up to 350 MHz configurable as HCSL, LVPECL, LVDS, or dual LVCMOS outputs. The highly integrated device consolidates four differential or eight single-ended clock generators and can store up to four different configuration settings, helping to minimize board space and bill-of-materials. Upon request, devices may be factory-programmed to the customer’s desired configuration.

Presented by Baljit Chandhoke, product line manager at IDT. Visit the Programmable Clocks page for more information.

Lab demonstration and clock jitter measurement showing VersaClock 5. The frequency analyzer shows phase jitter at approximately 575 picoseconds RMS. Presented by Baljit Chandhoke, product manager at IDT. For more information visit the Programmable Clocks page.

VersaClock® 5 is a low-power programmable clock generator with best-in-class jitter performance with less than 0.7psec RMS phase jitter from 12KHz to 20MHz. The highly integrated device consolidates four differential or eight single-ended clock generators and can store up to four different configuration settings, helping to minimize board space and bill-of-materials. The high-performance clock generator operates at less than 100mW core power (50 percent lower than competing devices), helping to ease system thermal constraints and reduce operating power expenses.

VersaClock 5 can take a crystal or a clock input. It has 4 fractional output dividers which allow the programming of 4 independent frequencies up to 350MHz. The four universal output pairs are independently configurable as HCSL, LVPECL, LVDS, or dual LVCMOS outputs. It also features a reference clock output. The fractional output dividers driving each output pair are easily programmed via I2C while the device is operating in the system, lending itself to system tuning and margin testing. Unlimited in-system reprogramming is possible via I2C, whereas four banks of one-time programmable non-volatile memory provide flexibility for multi-project inventory consolidation or design changes in field or production units. Upon request, devices may be factory-programmed to the customer's desired configuration.

Presented by Baljit Chandhoke, Product Marketing Manager at Integrated Device Technology, Inc.

This is a video introduction and demonstration of the VersaClock 5 Evaluation Board. This device uses Renesas's Timing Commander™ software platform, allowing engineers to configure and program their devices with an intuitive, time-saving graphical user interface (GUI).

The 5P49V5901 is an in-system programmable clock generator featuring four universal output pairs capable of producing independent frequencies up to 350 MHz in various output types. With RMS phase jitter less than 0.7 picoseconds over the full 12 kHz to 20 MHz integration range, the new device meets the stringent jitter requirements of PCI Express® Gen 1/2/3, USB 3.0, and 1G/10G Ethernet. The high-performance clock generator operates at less than 100 mW core power (50 percent lower than competing devices), helping to ease system thermal constraints, reduce operating power expenses, and maximize battery life.

The 5P49V5901's four universal output pairs are each independently configurable as HCSL, LVPECL, LVDS, or dual LVCMOS outputs. The fractional output dividers driving each output pair are easily programmed via I2C while the device is operating in the system, lending itself to system tuning and margin testing. Unlimited in-system reprogramming is possible via I2C, whereas four banks of one-time programmable non-volatile memory provide flexibility for multi-project inventory consolidation or design changes in field or production units. Upon request, devices may be factory-programmed to the customer's desired configuration.

Presented by Shudong Zheng, Sr. Design Engineer at IDT. For more information about Renesas's VersaClock 5, visit our VersaClock5 page.

Description

IDT's innovative support tool, Timing Commander™, expedites development cycles by empowering customers to program sophisticated timing devices with an intuitive and flexible Graphical User Interface. IDT's Timing Commander is a Windows™-based platform designed to serve user-friendly configuration interfaces, known as personalities, for various IDT products and product families. With a few simple clicks, the user is presented with a comprehensive, interactive block diagram offering the ability to modify desired input values, output values, and other configuration settings. The software automatically makes calculations, reports status monitors, and prepares register settings without the need to reference a datasheet. The tool also automatically loads the configuration settings over USB to an IDT evaluation board for immediate application in the circuit. Once the device has been configured and tuned for optimal system performance, the configuration file can be saved for factory-level programming before shipment. For more information about Timing Commander, visit our Timing Commander page.

Renesas's innovative support tool, Timing Commander™, expedites development cycles by empowering customers to program sophisticated timing devices with an intuitive and flexible Graphical User Interface. Renesas's Timing Commander is a Windows™-based platform designed to serve user-friendly configuration interfaces, known as personalities, for various Renesas products and product families. With a few simple clicks, the user is presented with a comprehensive, interactive block diagram offering the ability to modify desired input values, output values, and other configuration settings. The software automatically makes calculations, reports status monitors, and prepares register settings without the need to reference a datasheet. The tool also automatically loads the configuration settings over USB to an Renesas evaluation board for immediate application in the circuit. Once the device has been configured and tuned for optimal system performance, the configuration file can be saved for factory-level programming prior to shipment. Presented by Steven Gutierrez, Senior Product Application Engineer at Renesas.

Resources

Timing Commander

News & Blog Posts

News

May 20, 2015

IDT Introduces VersaClock 5 Programmable Clock Generator with Integrated Crystal

Support Communities

5P49V5933无时钟输出
用Timing Commander获取配置5P49V5933的寄存器的值，进行i2c通讯配置后，芯片不输出时钟。我想问问我使用软件配置的是否正确。还有芯片是 ...
May 8, 2026
- Analog Products
- Clocks & Timing
Alternate part
Hi all,We are redesigning project right now we need alternate for 5P49V5933B000LTGI this component. I am kindly requesting you to share the details with unit price, lead time, ROHS status, and reference design
Jul 13, 2024
- Analog Products
- Clocks & Timing

Support Communities

Get quick technical support online from Renesas Engineering Community technical staff.

Knowledge Base

Browse our knowledge base for helpful articles, FAQs, and other useful resources.

Browse Articles

Submit a Ticket

Submit a Ticket

Need to ask a technical question or share confidential information?

Resources

Customize Part