Overview
Description
The E10A-USB emulator is an on-chip debugging emulator which supports the development for systems using microcomputers of the SuperH RISC engine family, the H8SX family, and the H8S family. As the main body of the E10A-USB emulator is connected to the user system via the dedicated debug interface (H-UDI and AUD), you can debug in such a form close to the completed product.
Features
- Breakpoints
- Hardware Breakpoints, dependent on device specification
- 255 software breakpoints
- User break
- Trace functions
- 4 branch trace messages stored on device H-UDI capable devices
- Real time branch trace with AUD capable devices -HS0005KCU02H only
- RAM monitor
- The contents of a memory can be referenced and changed during program execution in real-time with AUD capable devices.
- Full source level debug
- Support for Renesas , IAR and GNU compilers
- Host requirement
- PentiumR3 600MHz or greater
- RAM 128MB or greater
- Available hard-disk 50MB or greater
- USB rev 1.1 port
- User I/F
- 14-way connector (Type: 2514-6002: [3M Co., Ltd.])
- 36-way connector (Type: DX10M-36S: [Hirose Electric Co., Ltd.])
- Learn More
Release Information
Target Devices
Design & Development
Additional Details
Lineup
See the product pages for the details of each model below.
| Item | Description | ||
|---|---|---|---|
| Products | HS0005KCU01H for the H-UDI interface Note1 Image  | HS0005KCU02H for the AUD trace function Note2 Image  | HS0005KCU14H for the Multi-core MCUs of SuperH RISC engine Family Image  |
| MCUs |
| ・Multi-core MCUs of SuperH RISC engine Family | |
Notes
- The H-UDI (User Debugging Interface) is an interface compatible with the Joint Test Action Group (JTAG) specifications.
- The AUD (Advanced User Debugger) trace is the large-capacity trace function that is enabled when the AUD pins are connected to the emulator. When an event that starts trace acquisition occurs, the trace information is output in realtime from the AUD pins. For more details, refer to On-Chip Debugger Functional Overview (PDF | English, 日本語).
Support
Support Communities
- How do you disable watchdog on SH3 7706 via Workbench when debugging w/ E10a-USB
I could probably go in and tweak the register every session as it is memory mapped, but is there some setting in the Embedded Workbench to do that for all debugging sessions? I haven't been able to find it if there is. I'm using version 4.0.
Nov 21, 2019 - Error while connecting the E10A- USB Emulator and SH72531 to PC
Hi, I am using SH72531 and I have an E10A USB emulator (HS0005KCU02H). I am following the process given in Renesas SuperH Family E10A-USB Emulator User’s Manual. But whenever I try to connect the SH72531 and E10A USB Emulator to the host (Desktop PC), I am getting the ...
Oct 11, 2017 - MS7727CP02Y board with E10A-USB - debugging problem
Hi all,I've a MS7727CP02Y board (SH7727 processor) with T_Engine installed. I use an E10A-USB OCD to connect to the host computer.Right now I want to able to debug a simple applications (not T-Engine related) using Renesas HEW IDE.HEW is able to connect w ...
Aug 19, 2010
Knowledge Base
- Starting up E10A-USB for H8S or H8SX shows failure messages
... mounted to the system. Make sure the operating mode is set to a supported mode.Refer to section 2.1 [MCU Operating Modes] in the E10A-USB Emulator Additional Document for Users Manual for the target MCU Device-specific E10A-USB Emulator Additional Document for Users Manuals can be downloaded ...
Jun 10, 2011 - How to change device group after "Setup tool for E10A-USB Emulator"?
... allows you to install additional device group to the E10A-USB emulator. Device Group Addition is software product allows another device group available with the E10A-USB emulator. It is offered in CD-ROM, and varies with the group of device. Since one E10A-USB emulator needs one license tool ...
Sep 10, 2007 - How to properly download program in E10A USB Writing Flash memory mode?
This message indicates the program was downloaded to the address other than in the internal ROM area on the MCU. Refer to the map file to see if data exist in an address other than the on-chip ROM area, and modify your program so that the data is assigned ...
Mar 12, 2008
Support Communities
