Overview
Description
The ISL80410 is a high voltage, adjustable VOUT, low quiescent current linear regulator ideally suited for “always-on” and “keep alive” applications. The ISL80410 operates from an input voltage of +6V to +40V under normal operating conditions and consumes only 18µA of quiescent current at no load. The ISL80410 features an EN pin that can be used to put the device into a low-quiescent current shutdown mode in which it draws only 2µA of supply current. The device features over-temperature shutdown and current limit protection. The ISL80410 is rated to operate across the -40°C to +125°C temperature range and is available in an 8 Ld Small Outline Exposed Pad Plastic Package (EPSOIC).
Features
- Wide VIN range of 6V to 40V
- Adjustable output voltage from 2.5V to 12V
- Ensured 150mA output current
- Ultra low 18µA typical quiescent current
- Low 2µA of typical shutdown current
- ±1% accurate voltage reference (over temperature, load)
- Low dropout voltage of 295mV at 150mA
- Low 26µVRMS noise
- 40V tolerant logic level (TTL/CMOS) enable input
- Stable operation with 10µF output capacitor
- 5kV ESD HBM rated
- Thermal shutdown and current limit protection
- 8 Ld exposed pad EPSOIC package
Comparison
Applications
Documentation
Featured Documentation
Log in required to subscribe
|
|
|
|
|---|---|---|
| Type | Title | Date |
| Datasheet | PDF 850 KB | |
| Brochure | PDF 12.71 MB 日本語 | |
| Product Advisory | PDF 314 KB | |
| Application Note | PDF 509 KB | |
| Application Note | PDF 397 KB | |
5 items
|
||
Design & Development
Boards & Kits
Evaluation
ISL80410EVAL1Z
Active
40V, Low Quiescent Current, 150mA Linear Regulator Evaluation Board
The ISL80410EVAL1Z evaluation board is designed to demonstrate the performance of the ISL80410 high voltage linear regulator. The board is available with jumpers to set the output voltage from 2.5V to 12V by configuring a single resistor. It can also be configured to give a specific output...
Recommended Documents:
Reference Designs
RX23E-A-DL
Active
RX23E-A Tiny Board for Digital Loadcell Reference Design
This is a reference design of a digital load cell using an MCU with a high-precision analog front-end (AFE), the RX23E-A. Using the RX23E-A makes an external dedicated AFE unnecessary, thereby miniaturizing the board.
In the digital load cell, a board mounting ADC and MCU, and a load cell are...
Recommended Documents:
Reference Designs
RX23E-A-CH-IAMS
Active
RX23E-A Channel-to-Channel Isolated Analog Input Module Reference Design
This is a reference design of a system that incorporates four pieces of RX23E-A with channel-to-channel isolation and measures temperature and voltage synchronously. This is ideal for applications, such as an analog input module with multiple analog inputs, a temperature controller, a recorder,...
Recommended Documents:
Reference Designs
RX23E-B-QFN40-WT
Active
RX23E-B Digital Load Cell Tiny Board Reference Design
The RX23E-B Digital Load Cell Tiny Board Reference Design is a compact and efficient solution for digital load cell design that utilizes the RX23E-B 32-bit microcontroller. This microcontroller integrates a high-speed, high-precision analog front-end (AFE), which negates the necessity for a...
Recommended Documents:
Reference Designs
RX23E-B-QFP64-FT
Active
RX23E-B 6-Axis Force Sensor Small Board Reference Design
The RX23E-B 6-Axis Force Sensor Small Board Reference Design is a compact solution that utilizes the RX23E-B 32-bit microcontroller (MCU). This MCU integrates a high-speed, high-precision analog front-end (AFE), which negates the necessity for a dedicated AFE, thereby minimizing the board...
Development
RX23E-A-IO-LINK-TEMP-SENSOR
Active
RX23E-A IO-Link Temperature Sensor Solution Development Kit
This single-chip solution uses the 32-bit RX23E-A microcontroller with built-in high-precision analog front-end (AFE) to measure temperature, process sensing and signals, and control IO-Link communications via a ZIOL2401 IO-Link PHY chip.
Recommended Documents:
Evaluation
INVB-LV-RZT-I
Active
RZ/T Series Inverter Board
The RZ/T Series Inverter Board (P/N: RTK0EM0000B15010BJ) is an inverter board that allows users to evaluate motor control using a BLDC motor with ease. This product supports absolute encoder and incremental encoder. By using in combination with a compatible CPU board, users can immediately start...
Recommended Documents:
Evaluation
INVB-LV-RZT-B
Active
RZ/T Series Inverter Board Kit
The RZ/T Series Inverter Board Kit (P/N: RTK0EM0000S05010BJ) is an inverter board that allows users to evaluate motor control using BLDC motor with ease. This product supports absolute encoder and incremental encoder. By using in combination with a compatible CPU board, users can immediately...
Recommended Documents:
Evaluation
BUSB-RZT2H-B
Active
Bus Board for RZ/T2H
The Bus Board for RZ/T2H is an interface board for the RZ/T Series Inverter Board (P/N: RTK0EM0000B15010BJ or RTK0EM0000S05010BJ) and the RZ/T2H Evaluation Board Kit (P/N: RTK9RZT2H0S00000BJ). This product makes it easy to connect up to nine RZ/T Series Inverter Boards.
Supported CPU Board:...
Recommended Documents:
Reference Designs
RX23E-A-TEC
Active
RX23E-A Thermoelectric Peltier Controller Reference Design
This is a reference design of a thermoelectric Peltier controller using an high-precision AFE-mounted MCU, RX23E-A. It is capable of realizing measurement, calculation and the control necessary to perform temperature control with a single RX23E-A chip,
The Thermoelectric Peltier Controller...
Recommended Documents:
Models
ECAD Models
Schematic symbols, PCB footprints, and 3D CAD models from SamacSys can be found by clicking on the CAD Model links in the Product Options table. If a symbol or model isn't available, it can be requested directly from SamacSys.
Product Options
Applied Filters: