Overview
Description
[Notes] Renesas Emulator and Flash Memory Programmer Products with a USB Interface Notice Regarding Changes to Windows Driver Policy (PDF | English, 日本語)
The E10A-USB emulator is an on-chip debugging emulator which supports the development for systems using microcomputers of the SuperH RISC engine family, the H8SX family, and the H8S family. As the main body of the E10A-USB emulator is connected to the user system via the dedicated debug interface (H-UDI and AUD), you can debug in such a form close to the completed product.
Features
- Breakpoints
- Hardware Breakpoints, dependent on device specification
- 255 software breakpoints
- User break
- Trace functions
- 4 branch trace messages stored on device H-UDI capable devices
- Real time branch trace with AUD capable devices -HS0005KCU02H only
- RAM monitor
- The contents of a memory can be referenced and changed during program execution in real-time with AUD capable devices.
- Full source level debug
- Support for Renesas , IAR and GNU compilers
- Host requirement
- PentiumR3 600MHz or greater
- RAM 128MB or greater
- Available hard-disk 50MB or greater
- USB rev 1.1 port
- User I/F
- 14-way connector (Type: 2514-6002: [3M Co., Ltd.])
- 36-way connector (Type: DX10M-36S: [Hirose Electric Co., Ltd.])
- Learn More
Release Information
Target Devices
Design & Development
Additional Details
Lineup
See the product pages for the details of each model below.
| Item | Description | ||
|---|---|---|---|
| Products | HS0005KCU01H Image  | HS0005KCU02H Image  | HS0005KCU14H Image  |
| MCUs |
| ・Multi-core MCUs of SuperH RISC engine Family | |
Notes
- The H-UDI (User Debugging Interface) is an interface compatible with the Joint Test Action Group (JTAG) specifications.
- The AUD (Advanced User Debugger) trace is the large-capacity trace function that is enabled when the AUD pins are connected to the emulator. When an event that starts trace acquisition occurs, the trace information is output in realtime from the AUD pins. For more details, refer to On-Chip Debugger Functional Overview (PDF | English, 日本語).
Support
Support Communities
- Technical Support Request: Flashing SH726306200FP via E10A-USB Emulator
Hi Team. I am currently developing with the SH2A series MCU and am seeking guidance on the flash programming process using the E10A-USB emulator. As I am new to this specific controller, I would also appreciate recommendations for any alternative flashing methods or tools that might be more streamlined ...
Apr 29, 2026 - WTB: Used E10a-USB red or yellow programmed for SH3 7706 (H-UDI debugger)
This is probably a long shot that someone would have one of these, but the folks at Renesas support suggested I post an inquiry here. If this is not the correct forum to post this, I will remove and post there. thanks!
Sep 26, 2019 - How do you disable watchdog on SH3 7706 via Workbench when debugging w/ E10a-USB
I could probably go in and tweak the register every session as it is memory mapped, but is there some setting in the Embedded Workbench to do that for all debugging sessions? I haven't been able to find it if there is. I'm using version 4.0.
Nov 21, 2019
Knowledge Base
- Can these E8a, E8, E10A-USB and E10T-USB emulators be used in 1 PC?
... at the same time, the channel or serial number* for each emulator will appear in the Driver details dialog when the PC is turned on.* Display message:E10A-USB/E10T-USB/E8: channelE8a: serial numberTo switch emulators, select the corresponding channel or serial number. (refer to figure below)
Mar 31, 2009 - What is the cause if I use E10A USB and it will not run whether I select MCU?
H8SX/1651 Group:This message is displayed when the EMLE pin on the H8SX/1651 Group MCU is set to low. When using the E10A-USB, make sure the EMLE pin on the H8SX/1651 Group MCU is set to high. SH7080 Series, SH7146 Series, SH7149 Series ...
Apr 13, 2011 - In E10A-USB, the write operation failed from H'200000 on
Valid address paths for H8SX/1651 Group initial values goes up to A20 (up to address H'200000). The only valid CS signal is CS0 (H'0~H'1FFFFF). To use addresses beyond H'200000, set the port function controller to enable address paths from A21 and beyond, CS1 ...
Jun 14, 2011
Support Communities
