Product Status: Mass Production
OVERVIEW
The ISL78228 is a high efficiency, dual synchronous step-down DC/DC regulator that can deliver up to 800mA continuous output current per channel. The supply voltage range of 2.75V to 5.5V allows for the use of a 3.3V or 5V input. The current mode control architecture enables very low duty cycle operation at high frequency with fast transient response and excellent loop stability. The ISL78228 operates above the AM radio band as well as the 2.25MHz switching frequency, allowing for the use of small, low cost inductors and capacitors. Each channel is optimized for generating an output voltage as low as 0.6V.
The ISL78228 has a user configurable mode of operation-forced PWM mode and PFM mode. The forced PWM mode operation reduces noise and RF interference while the PFM mode operation provides high efficiency by reducing switching losses at light loads. In PFM mode of operation, both channels draw a total quiescent current of only 30µA, hence enabling high light-load efficiency in order to maximize battery life.
The ISL78228 offers a 1ms power-good (PG) to monitor both outputs at power-up. When shut down, ISL78228 discharges the output capacitor. Other features include internal digital soft-start, enable for power sequence, overcurrent protection, and thermal shutdown. The ISL78228 is offered in a 3mmx3mm 10 Ld DFN package with 1mm maximum height. The complete converter occupies less than 1.8cm2 area.
The ISL78228 is AEC-Q100 qualified and is rated for the automotive temperature range (-40°C to +105°C).
The ISL78228 has a user configurable mode of operation-forced PWM mode and PFM mode. The forced PWM mode operation reduces noise and RF interference while the PFM mode operation provides high efficiency by reducing switching losses at light loads. In PFM mode of operation, both channels draw a total quiescent current of only 30µA, hence enabling high light-load efficiency in order to maximize battery life.
The ISL78228 offers a 1ms power-good (PG) to monitor both outputs at power-up. When shut down, ISL78228 discharges the output capacitor. Other features include internal digital soft-start, enable for power sequence, overcurrent protection, and thermal shutdown. The ISL78228 is offered in a 3mmx3mm 10 Ld DFN package with 1mm maximum height. The complete converter occupies less than 1.8cm2 area.
The ISL78228 is AEC-Q100 qualified and is rated for the automotive temperature range (-40°C to +105°C).
KEY FEATURES
- Internal current mode compensation
- 100% maximum duty cycle for lowest dropout
- Selectable forced PWM mode and PFM mode
- External synchronization up to 4MHz
- Start-up with prebiased output
- Soft-stop output discharge during disable
- Internal digital soft-start - 2ms
- Power-good (PG) output with 1ms delay
- AEC-Q100 qualified
- Pb-free (RoHS compliant)
BLOCK DIAGRAM
PARAMETRICS
Parameters
ISL78228
Basic Information
Production Status
Mass Production
iSim Model
YES
# of Outputs
2
Topology [Rail 1]
Buck
Input Voltage Min (V) [Rail 1]
2.75
Input Voltage Max (V) [Rail 1]
5.5
Output Voltage Min (V) [Rail 1]
0.6
Output Voltage Max (V) [Rail 1]
5.5
Output Current Max (A) [Rail 1]
0.8
IQ [Rail 1]
30 µA
Switching Freq. (max) (MHz)
2.7
Switching Freq. (min) (MHz)
1.8
Max Duty Cycle (%)
See Datasheet
Qualification Level
Automotive
Peak Efficiency (%)
96
POR
Yes
SYNCH Capability
Yes
Control Type
Current Mode
Switching Frequency Range (MHz)
2.25
Temperature Range
-40 to +105
Design Resources and Tools
Simulation Tool
iSim Online Designer
Select supporting components, build your schematic and validate your power management and op amp designs.
Selection Tool
PowerCompass Online Tool
The PowerCompass™ tool helps you find Renesas parts that match your requirements, performs system analysis & more.
Cross Reference
Intersil Cross Reference
Cross-reference based on data from industry sources. Support for the online tool has been discontinued, but the data is still available.
Knowledge Base
Automotive IC FAQs
Find answers to common questions, support articles and development hints.
