Overview
Description
[Updated: Jul. 21, 2026 Rev. 1.10] [Notes] Emulator and Flash Memory Programmer Products Notice Regarding Changes to Windows Driver Policy (PDF | English, 日本語)
The E10A-USB emulator is an on-chip debugging emulator which supports the development for systems using microcomputers of the SuperH RISC engine family, the H8SX family, and the H8S family. As the main body of the E10A-USB emulator is connected to the user system via the dedicated debug interface (H-UDI and AUD), you can debug in such a form close to the completed product.
Features
- Breakpoints
- Hardware Breakpoints, dependent on device specification
- 255 software breakpoints
- User break
- Trace functions
- 4 branch trace messages stored on device H-UDI capable devices
- Real time branch trace with AUD capable devices -HS0005KCU02H only
- RAM monitor
- The contents of a memory can be referenced and changed during program execution in real-time with AUD capable devices.
- Full source level debug
- Support for Renesas , IAR and GNU compilers
- Host requirement
- PentiumR3 600MHz or greater
- RAM 128MB or greater
- Available hard-disk 50MB or greater
- USB rev 1.1 port
- User I/F
- 14-way connector (Type: 2514-6002: [3M Co., Ltd.])
- 36-way connector (Type: DX10M-36S: [Hirose Electric Co., Ltd.])
- Learn More
Release Information
Target Devices
Design & Development
Additional Details
Lineup
See the product pages for the details of each model below.
| Item | Description | ||
|---|---|---|---|
| Products | HS0005KCU01H Image  | HS0005KCU02H Image  | HS0005KCU14H Image  |
| MCUs |
| ・Multi-core MCUs of SuperH RISC engine Family | |
Notes
- The H-UDI (User Debugging Interface) is an interface compatible with the Joint Test Action Group (JTAG) specifications.
- The AUD (Advanced User Debugger) trace is the large-capacity trace function that is enabled when the AUD pins are connected to the emulator. When an event that starts trace acquisition occurs, the trace information is output in realtime from the AUD pins. For more details, refer to On-Chip Debugger Functional Overview (PDF | English, 日本語).
Support
Support Communities
- WTB: Used E10a-USB red or yellow programmed for SH3 7706 (H-UDI debugger)
This is probably a long shot that someone would have one of these, but the folks at Renesas support suggested I post an inquiry here. If this is not the correct forum to post this, I will remove and post there. thanks!
Sep 26, 2019 - MS7727CP02Y board with E10A-USB - debugging problem
Hi all,I've a MS7727CP02Y board (SH7727 processor) with T_Engine installed. I use an E10A-USB OCD to connect to the host computer.Right now I want to able to debug a simple applications (not T-Engine related) using Renesas HEW IDE.HEW is able to connect w ...
Aug 19, 2010 - Error while connecting the E10A- USB Emulator and SH72531 to PC
Hi, I am using SH72531 and I have an E10A USB emulator (HS0005KCU02H). I am following the process given in Renesas SuperH Family E10A-USB Emulator User’s Manual. But whenever I try to connect the SH72531 and E10A USB Emulator to the host (Desktop PC), I am getting the ...
Oct 11, 2017
Knowledge Base
- Is an area reserved in H8S/2329EF can be also used in E10A-USB?
No. The areas that can be emulated by E10A-USB are the same as those shown in the memory map in the MCU hardware manual.
Mar 12, 2008 - Test program for E10A-USB emulator; error message appears
This message is displayed when a test program is executed with the E10A-USB connected to the user system. The test program can only be executed by the E10A-USB emulator alone. The user system interface cable must be removed before executing the test program.
Jun 10, 2011 - Error messages during E10A-USB emulator software start-up process
This message is displayed when you do not have a license for the selected device group when starting up the E10A-USB. Purchase of the E10A-USB comes with 1 device group license. To use other device groups, you need to buy a License Tool for Device Group Additions for ...
Jun 10, 2011
Support Communities
