Overview
Description
The SLG47104 provides a small, low power component for commonly used mixed-signal and bridge functions. The user creates their circuit design by programming the one-time programmable (OTP) Non-Volatile Memory (NVM) to configure the interconnect logic, the IO pins, the high voltage pins, and the macrocells of the SLG47104. The configurable PWM macrocell in combination with special high voltage outputs will be useful for a motor drive or load drive applications. High voltage pins allow users to design smart level translators or to drive the high-voltage high-current load.
Features
- Two Power Supply Inputs
- 2.5V (±8 %) to 5.0V (±10 %) VDD
- 3.3V (±9 %) to 12.0V (±10 %) VDD2
- Two High Voltage High Current Drive GPOs
- Full Bridge Driver Option
- Dual/Single Half Bridge Driver Option
- Slew Rate Modes: Motor Driver Mode, Pre-Driver (MOSFET Driver) Mode
- SLEEP Function
- Low RDS(ON) High Side + Low Side resistance = 0.4Ω
- 2A Peak, 1.5A RMS per Full Bridge (at VDD2 = 5V, T = +25 °C)
- 2A Peak, 1.5A RMS per Half Bridge GPO (at VDD2 = 5V, T = +25 °C)
- Integrated Protections: Over Current Protection (OCP), Short Circuit Protection, Under-Voltage Lockout (UVLO), Thermal Shutdown (TSD)
- SENSE Input connected to the Current Comparator for Current Control
- Fault Signal Indicator for Full Bridge: OCP, UVLO, TSD
- Current Sense Comparator
- Dynamical VREF Mode
- High-Speed General Purpose ACMP
- Modes: UVLO, OCP, TSD, Voltage Monitor, Current Monitor
- Voltage Reference (VREF) Output
- Three Multi-Function Macrocells
- 2× Selectable DFF/LATCH/3-bit LUTs + 8-bit Delay/Counters
- 1× Selectable DFF/LATCH/4-bit LUT + 16-bit Delay/Counter
- Nine Combination Function Macrocells
- 2× Selectable DFF/LATCH or 2-bit LUTs
- 1× Selectable Pattern Generator or 2-bit LUT
- 3× Selectable DFF/LATCH or 3-bit LUTs
- 1× Selectable DFF/LATCH or 3-bit LUT or PWM Chopper
- 1× Selectable Pipe Delay or Ripple Counter or 3-bit LUT
- 1× Selectable DFF/LATCH or 4-bit LUT
- PWM Macrocell
- Flexible 8-bit/7-bit PWM Mode with Duty Cycle Control
- 16 Preset Duty Cycle Registers for Sine or Custom Waveforms
- Serial Communications
- I2C Protocol Interface
- Additional Logic
- Deglitch Filter with Edge Detectors
- Oscillators (OSC)
- 2.048kHz Oscillator
- 25MHz Oscillator
- Other Features
- Power-On Reset (POR)
- One-Time Programmable Memory
- Operating Temperature: -40°C to +85°C
- RoHS Compliant / Halogen-Free
- Package
- 20-pin STQFN: 2mm × 3mm × 0.55mm, 0.4mm pitch
Comparison
Applications
Documentation
Featured Documentation
Log in required to subscribe
|
|
|
|
|---|---|---|
| Type | Title | Date |
| Datasheet | PDF 5.58 MB | |
| Device Errata | PDF 670 KB | |
2 items
|
||
Design & Development
Software & Tools
Software & Tools
| Software title
|
Software type
|
Company
|
|---|---|---|
| Go Configure Software Hub Go Configure Software Hub provides development support for a variety of products, including GreenPAK configurable mixed signal matrix and ForgeFPGA™ devices.
|
Software Package | Renesas |
1 item
|
||
Boards & Kits
Development
SLG47104V-SKT
Active
HVPAK SLG47104V Development Kit with Socket Adapter
The SLG47104V-SKT is a socket adapter kit for use with the SLG4DVKADV GreenPAK™ Advanced Development Board or SLG4DVKLITE GreenPAK Lite Development Board. The SLG47104V-SKT kit includes the SLG4SA20HV-20x30 socket adapter and 50 SLG47104V HVPAK™ programmable mixed-signal matrix IC samples.
Used...
Recommended Documents:
Development
SLG4DVKADV
Active
GreenPAK Advanced Development Board
The GreenPAK™ Advanced Development Board provides full programming, emulation, and testing functions for the GreenPAK devices - for use with SLG46xxxX-SKT/SLG47xxxV-SKT socket kits.
It works in tandem with the GreenPAK Designer software (built into the Go Configure™ Software Hub), and it allows...
Recommended Documents:
Test This Board Remotely
Available on Lab on the Cloud, use our PC-based GUI to instantly start configuring and testing designs in our virtual lab, no physical board needed.
Development
SLG4DVKLITE
Active
GreenPAK Lite Development Board
The GreenPAK™ Lite Development Board provides full programming, emulation, and testing functions for GreenPAK devices, working in conjunction with the Go Configure™ Software Hub. Board functionality is provided by the RX66T MCU from Renesas.
Recommended Documents:
Models
ECAD Models
Schematic symbols, PCB footprints, and 3D CAD models from SamacSys can be found by clicking on the CAD Model links in the Product Options table. If a symbol or model isn't available, it can be requested directly from SamacSys.
Product Options
Applied Filters:
Support
Support Communities
Get quick technical support online from Renesas Engineering Community technical staff.
