接口&连接

瑞萨 RS-232 和 RS-485/422 收发器的历史可以追溯到 20 世纪 70 年代,如今我们仍是市场领导者。 客户正在寻找的无论是基础的低成本产品或拥有附加功能的增强型产品,我们几乎应有尽有。

Six Ways Renesas Enhances Your Serial Port

IEC 61000 Enhanced ESD Protection

Full-featured transceivers include improved ESD protection on bus pins that connect to an exposed port on a piece of equipment. Exposure makes the port susceptible to ESD events. Even connecting a charged interface cable could destroy an unprotected transceiver.

ESD protection falls under two standards: Human Body Model (HBM) standard and the IEC 61000-4-2 (IEC). The HBM test emulates the types of ESD events seen during manufacturing and handling, while the IEC ESD test is an end equipment test intended to harden equipment to ESD events seen in the field.

The special ESD structures utilized in Renesas' full-featured families allow these transceivers to meet the highest level for each of the standards.

Ruggedized Fault Protected: Overvoltage Protected (OVP)

Overvoltage protected, or fault protected, transceivers are designed so that the RS-485 bus pins can handle voltages much higher than those required by the RS-485 standard. This protects the device when power is routed in the same conduit as the data cable.

Intersil devices also feature a wide common mode voltage range (CMR) to compensate for the common mode voltage pick-up that occurs in long networks and noisy environments.

The ±16.5kV HBM ESD, the OVP and wide CMR features combined make the Renesas devices some of the most robust transceivers available.

High-Speed Transceivers

Applications like robotics, motor control and data acquisition require high data rates for minimal latency and increased throughput. Renesas' full-featured, high-speed family specifies the maximum Rx and Tx skews at 1.5ns, and the maximum part-to-part skew at 4ns.

  • ISL3179E (3V) and ISL3159E (5V) are specified at 40Mbps
  • ISL3259E (5V) operates at data rates up to 100Mbps
  • ISL3159E and ISL3259E have a Tx VOD > 2.1V (for high-speed PROFIBUS DP networks)
  • 125 °C option to compensate for high temperatures in motor control applications
  • MSOP and DFN packages available

Low Voltage & Low Power

Most current generation RS-485 families have a “hot plug” function that disables the device when Vcc drops considerably below its nominal voltage (e.g., at 2.5V for Vcc = 3.3V), so 2.5V or 1.8V applications require ICs specifically designed for those operating voltages.

Single Tx (ISL32614E), Single Rx (ISL32610E), and Transceivers (ISL32602/603E) designed for low operating voltages:

  • Operate from voltages as low as 1.8V
  • Feature quiescent supply currents (Icc) as low as 80µA
  • Operate at data rates as high as 256kbps (Applications requiring higher data rates can use the ISL32603E or ISL32614E at 460kbps by powering them from a 3.3V supply)

Power critical applications such as remote sensor links and battery-operated security systems benefit from this level of performance.

Low-Cost Transceivers

Short, simple, low-node-count networks can often use low-cost RS-485 transceivers.

  • Short networks don't pick up much common mode voltage (CMV) and do not need more than the standard CMR or overvoltage protection (OVP).
  • Simple networks with ≤ 32 nodes do not require fractional unit load devices, and electrostatic discharge (ESD) protection may not be required. (Although some basic devices do include ±8kV to ±15kV Human Body Model ESD protection).
  • RS-422 networks with single, always enabled drivers, do not require bus biasing because the bus is constantly driven.
  • An electrically short bus does not need to be treated as a transmission line and does not require bus termination. (This may not apply in multi-driver systems).

Multiprotocol

Many applications need both an RS-232 and RS-485 serial port. The dual protocol devices integrate both transceivers into a single package. The single-channel device can be programmed for either interface. The two-channel configuration is very flexible as each channel can be either port.

Both 3.3V and 5V supply options are available. An in-line package and a more compact QFN package are available. The QFN package has additional features including a logic supply pin (VL) and selectable RS-485 data rates. The RS-232 data rate can operate up to 400kbps.

分类

多协议 RS-485/422 和 RS-232

将 RS-232 和 RS-485 收发器集成到单一封装中的器件

RS-232

具有高达 1Mbps 的数据速率、ESD 保护、低功耗关断模式的收发器

RS-485/RS-422

各种速率等级的半双工和全双工收发器

文档

文档标题 类型 日期 升序排列
PDF472 KB
应用文档
PDF2.72 MB日本語
手册
PDF188 KB
技术摘要
PDF920 KBEnglish
白皮书
PDF918 KBEnglish
白皮书
PDF195 KB
白皮书
PDF246 KBEnglish
白皮书
PDF624 KB
白皮书
PDF437 KB
白皮书
PDF307 KB
白皮书
 

视频和培训

How to Design with High-Speed RS-485 Transceivers

This introduction to high-speed RS-485 designs will introduce you to standard and high-speed RS-485 networks, discuss signal degradation on the bus, review key transceiver requirements for high-speed transmission and give you some design tips for system and bus node designs as well as general high-speed design guidelines.