Product Status: Mass Production
OVERVIEW
The ISL85003 and ISL85003A are synchronous buck regulators with integrated high-side and low-side FETs. The regulator can operate from an input voltage range of 4.5V to 18V while delivering a very efficient continuous 3A current. This is all delivered in a very compact 3mmx4mm DFN package.
The ISL85003 is designed on Intersil’s proprietary fab process that is designed to deliver very low rDS(ON) FETs with an optimized current mode controller wrapped around it. The high-side NFET is designed to have an rDS(ON) of 65mΩ while the low-side NFET is designed to have an rDS(ON) of 45mΩ. With these two FETs, the device delivers very high efficiency power to the load.
The ISL85003 can automatically switch between DCM and CCM for light-load efficiency in DCM. The switching frequency in CCM is internally set to 500kHz.
The device provides a maximum static regulation tolerance of ±1% over wide line, load and temperature ranges. The output is user adjustable, with external resistors, down to 0.8V. Pulling EN above 0.6V enables the controller. The regulator supports prebiased output.
Fault protection is provided by internal current limiting during positive or negative overcurrent conditions, output and input under and overvoltage detection and an over-temperature monitoring circuit.
The ISL85003 is designed on Intersil’s proprietary fab process that is designed to deliver very low rDS(ON) FETs with an optimized current mode controller wrapped around it. The high-side NFET is designed to have an rDS(ON) of 65mΩ while the low-side NFET is designed to have an rDS(ON) of 45mΩ. With these two FETs, the device delivers very high efficiency power to the load.
The ISL85003 can automatically switch between DCM and CCM for light-load efficiency in DCM. The switching frequency in CCM is internally set to 500kHz.
The device provides a maximum static regulation tolerance of ±1% over wide line, load and temperature ranges. The output is user adjustable, with external resistors, down to 0.8V. Pulling EN above 0.6V enables the controller. The regulator supports prebiased output.
Fault protection is provided by internal current limiting during positive or negative overcurrent conditions, output and input under and overvoltage detection and an over-temperature monitoring circuit.
KEY FEATURES
- Input voltage range 4.5V to 18V
- Output voltage adjustable from 0.8V, ±1%
- Efficiency up to 95%
- Integrated boot diode with undervoltage detection
- Current mode control
- DCM/CCM
- Internal or external compensation options
- 500kHz switching frequency option
- External synchronization up to 2MHz on ISL85003
- Adjustable soft-start time on the ISL85003A
- Open-drain PG window comparator
- Built-in protection
- Positive and negative overcurrent protection
- Overvoltage and thermal protection
- Input overvoltage protection - Small 12 Ld 3mmx4mm Dual Flat No-Lead (DFN) package
BLOCK DIAGRAM
PARAMETRICS
Parameters
ISL85003
Basic Information
Production Status
Mass Production
iSim Model
YES
# of Outputs
1
Topology [Rail 1]
Buck
Input Voltage Min (V) [Rail 1]
4.5
Input Voltage Max (V) [Rail 1]
18
Output Voltage Min (V) [Rail 1]
0.8
Output Voltage Max (V) [Rail 1]
15
Output Current Max (A) [Rail 1]
3
IQ [Rail 1]
3.2 mA
Switching Freq. (max) (MHz)
0.6
Switching Freq. (min) (MHz)
0.4
Max Duty Cycle (%)
See Datasheet
Qualification Level
Standard
Peak Efficiency (%)
95
POR
Yes
SYNCH Capability
Yes
Control Type
Current Mode
Switching Frequency Range (MHz)
0.5
Can Sample
YES
Temperature Range
-40 to +125
Design Resources and Tools
Selection Tool
PowerCompass Online Tool
The PowerCompass™ tool helps you find Renesas parts that match your requirements, performs system analysis & more.
Design Tool
PowerNavigator Software
Configure and monitor digital-DC devices. Easily change features and functions of your power supply design with a simple GUI.
Simulation Tool
iSim Online Designer
Select supporting components, build your schematic and validate your power management and op amp designs.
Cross Reference
Intersil Cross Reference
Cross-reference based on data from industry sources. Support for the online tool has been discontinued, but the data is still available.
Knowledge Base
Switching Regulators FAQs
Find answers to common questions, support articles and development hints.
